What do I need to hang a lamp from the ceiling?

To hang a pendant lamp from a ceiling, you need a canopy (ceiling rose) to cover the electrical junction, a textile or PVC cable rated H03VV-F 3×0.75 mm² for the suspension and wiring, a lamp holder (such as E27 or E14) with an integrated strain relief to protect the electrical connections, and a suitable bulb. For heavier luminaires, a ceiling hook or mounting bracket rated for the lamp's weight is also required. All these components are available individually so you can assemble exactly the configuration you need.

What are the three main types of lamp sockets?

The three principal lamp socket families are: screw bases (Edison), including E14, E27 and E40, where the lamp is twisted into the holder; bayonet caps, such as B22d, where the lamp is pushed in and rotated to lock; and pin bases, which cover a wide range including GU10, GU5.3, G9, G4, G13 and R7s, where one or more pins make the electrical contact. Each family is further divided by pin spacing, voltage rating and maximum wattage, so always check the full socket designation before ordering a replacement holder or lamp.

Can lamp shades be replaced without buying a new luminaire?

Yes — lamp shades can be replaced independently in most standard luminaires. Replacement shades are available in fabric, glass, metal and plastic, and attach to the fitting via a spider frame, a ring adapter or a direct screw fitting (typically M10×1 thread). When ordering a replacement shade, note the fitting diameter, the attachment method and the maximum wattage the shade material can tolerate. Replacing a shade is a cost-effective way to refresh the look of a luminaire or repair damage, and it is far more sustainable than discarding the entire fitting.

What are the four main types of luminaires?

The four principal luminaire types are: pendant luminaires, which hang from the ceiling on a cable, rod or chain; surface-mounted luminaires, fixed directly to the ceiling or wall; recessed luminaires, installed flush into a ceiling void or wall recess; and track-mounted luminaires, clipped onto a 1-phase or 3-phase track rail for flexible, repositionable lighting. Each type requires specific accessories — canopies and suspension hardware for pendants, mounting frames for recessed fittings, and track adapters and feed-ins for track systems.

Which spare parts are available for older lamps and luminaires?

A wide range of spare parts is available for older luminaires, including replacement lamp holders (E27, E14, G9, GU10 and more), lamp shades and replacement glasses, canopies, strain reliefs, screw rings, cord switches, threaded rods and hex nuts, textile and PVC cables, and ballasts or starters for fluorescent fittings. In many cases, repairing an existing luminaire with genuine spare parts is both more economical and more environmentally responsible than replacing the entire fitting. If you are unsure which part you need, our contact and service team can help identify the correct component.

Which accessories do I need for a track lighting system?

A complete track lighting installation requires: the track rail itself (1-phase or 3-phase, surface-mounted, recessed or pendant); a live end feed-in to connect the track to the mains supply; straight connectors, L-joiners or T-joiners if the track run changes direction; end caps to seal open track ends safely; track adapters for each spotlight; and, for pendant track installations, wire rope suspension kits with adjustable ceiling anchors. For 3-phase systems, you will also need to plan which spotlights connect to which circuit to enable independent switching of different lighting zones.

What is the difference between a conventional ballast (CCG) and an electronic ballast (ECG)?

A conventional ballast (CCG) uses a magnetic iron-core inductor to limit current to fluorescent or discharge lamps. It operates at mains frequency (50 Hz), which can cause visible flicker, and consumes 10–15 % more energy than the lamp wattage alone. A separate starter is required. An electronic ballast (ECG) operates at 40–50 kHz, eliminating flicker, improving lamp efficacy by up to 20 %, and removing the need for a starter. ECG units are lighter, run cooler and are the preferred choice for offices, retail environments and any application where light quality matters. Both types must be matched to the lamp wattage.

Which luminaire accessories are best suited for retail and hospitality environments?

For retail shops, restaurants and showrooms, the most important luminaire accessories are 3-phase track system components — Eutrac feed-ins, adapters, connectors and suspension kits — which allow flexible, independently controlled accent and ambient lighting. High-CRI LED drivers (CRI ≥ 90) paired with dimmable spotlights ensure merchandise and interiors are shown at their best. For hospitality settings with a vintage or retro aesthetic, brass E27 lamp holders, textile cables in coordinating colours and decorative canopies create the warm, characterful atmosphere that guests expect. IP44-rated accessories are essential wherever luminaires are installed in outdoor terraces or kitchen areas.

Close menu

Leuchtmittel-Verkauf englisch

Accessories for lighting

Categories

Accessories for 1 Phase track

show

Accessories for 3 Phase track

1611 Articles

Sorting

Express delivery possible

Socket

GU10
G13
E27

Luminous flux (Lumen)

from 350 to 4100

Colour temperature (Kelvin)

from 2600 to 6500

Nominal voltage (Volt)

from 3 to 600

Power (Watt)

from 0.1000000015 to 4000

Light colour

Warm white
Neutral white
Daylight white
Neutral white

Dimmable

Illuminant type

LED lamp

Manufacturer

American DJ
Artecta
Eurolite
Eutrac
ISOLED
Ledvance
Osram
Riggatec
Showtec
SLV

Price

from 0.32 to 8326

9 From 68 pages

Products per page

No results were found for the filter!

SLV LED POWER SUPPLY 50W 24V TRIAC DIMMABLE

TRIAC dimmable LED power supply with maximum output of 50 W with a voltage of 24 V. : Product name: LED NETZTEIL • Colour: white • Material: polycarbonate (PC) • Dimmable: Yes...

€43.31 *

incl. tax, plus shipping costs

Availability:

Delivery time: 3-5 days

Delivery time: 3-5 days

PUNKTAUSLASS für EUTRAC Hochvolt 3Phasen-Aufbauschiene, grau

POINT OUTLET for EUTRAC 240V 3-phase surface-mounted track, silver-grey

Ceiling plate for luminaires with built-in 240V 3-phase track adapter. : Product name: EUTRAC® • Colour: grey • Material: plastic • Protection category: I • Assembly:...

€91.00 *

incl. tax, free shipping to Germany
[International shipping costs]

Availability:

Delivery time: 3-5 days

Delivery time: 3-5 days

Eutrac 3 Phasen T-Verbinder, Datenbus, außen rechts, schwarz

Eutrac 3 Phase T-Connector, Databus, outside right, black

T-connector with feed-in capability for the 240V 3-phase surface-mounted track System + Databus. Available in various colour versions, you can also choose the ground conductor's position left...